焊接機械手是一種通過在工件上移動焊機來幫助焊接過程的自動化加工設備,被認為是效率較高的機械,在制焊接行業中得到廣泛應用。下面來講講焊接機械手操作及保養規程吧。

Welding manipulator is an automatic processing equipment that helps the welding process by moving the welding machine on the workpiece. It is considered to be a highly efficient machine and is widely used in the manufacturing and welding industry. Let's talk about the safe operation and maintenance procedures of welding manipulator.

裝夾工藝：

Clamping process:

（1）模具安裝完畢后，將身體、頭部和手離開工作臺，保持距離并按下啟動開關；

(1) After the mold is installed, leave the body, head and hands off the workbench, keep a safe distance and press the start switch;

（2）將所需工件有序放入工裝，注意在用錘子敲打過程中工件飛出傷人；

(2) Put the required workpieces into the tooling in an orderly manner, and pay attention to the workpiece flying out and hurting people during the hammering process;

焊接完成：

Welding completion:

(1)焊接完成后，操作人員只能靠近工具轉動裝置的初始位置；

(1) After welding, the operator can only approach the initial position of the tool rotating device;

（2）將焊接好的工件有序、整齊地放置在料架內，不要高空放置，以免工件掉到地上傷到人員或設備；

(2) Place the welded workpiece in the material rack orderly and neatly, and do not place it at high altitude, so as to avoid the workpiece falling to the ground and injuring personnel or equipment;

(3)松開所有工裝上的壓緊裝置，取出焊接好的工件，一定要戴好手套等用品，防止燙傷皮膚和衣服；

(3) Loosen the pressing device on all tooling, take out the welded workpiece, and be sure to wear safety supplies such as gloves to prevent scalding skin and clothes;

焊接工藝：

Welding process:

（1）焊接過程中，一定要佩戴防護眼鏡，防止電弧灼傷眼睛或將物體濺入眼睛；

(1) During welding, be sure to wear protective glasses to prevent electric arc from burning eyes or splashing objects into eyes;

（2）開始焊接時，操作人員不能在機械手的工作范圍內，以防翻轉機械手或工裝時碰傷；

(2) When starting welding, the operator shall not be within the working range of the manipulator, so as to prevent the manipulator or tooling from being bruised when overturning;

（3）焊接過程中，嚴禁操作人員擅自離開現場，以防突發事件造成不必要的損失；

(3) During the welding process, it is strictly forbidden for operators to leave the site without authorization to prevent unnecessary losses caused by emergencies;

山東自動焊接設備廠家提醒您，機械手工作過程中，禁止非本類人員接近機械手工作區域，禁止擅自操作機械手。日常維護程序：

Shandong automatic welding equipment manufacturer reminds you that during the working process of the manipulator, non such personnel are not allowed to approach the working area of the manipulator, and it is forbidden to operate the manipulator without authorization. Routine maintenance procedures:

(1)每班清潔一次機器人表面的灰塵、油污和雜物；

(1) Clean the dust, oil and debris on the robot surface once a shift;

(2)檢查燃燒器，如有損壞或變形，更換備件并檢查原點；

(2) Check the burner. If it is damaged or deformed, replace the spare parts and check the origin;

（3）檢查裸露電纜的送絲管無磨損、劃痕，懸吊送絲管與電纜的彈簧、橡膠繩有無脫落、松脫現象，異常處理。

(3) Check whether the wire feed pipe of the exposed cable is free of wear and scratches, and whether the spring and rubber rope of the suspended wire feed pipe and the cable are free of falling off and loosening, and deal with abnormalities.

提醒您，每班下班前，應清理各自崗位上的雜物，打掃地面，打掃工作平臺，打掃設備，擺放整齊。更多相關內容就來關注我們網站http://www.agbet3.com吧！

Remind you that before each shift leaves work, you should clean up the sundries on your posts, clean the floor, clean the working platform, clean the equipment, and place them neatly. Follow our website for more relevant content http://www.agbet3.com Come on!